Personal computing discussed

Moderator: Captain Ned

 
morphine
Gold subscriber
Gerbilus Supremus
Posts: 11398
Joined: Fri Dec 27, 2002 8:51 pm
Location: Portugal (that's next to Spain)

Re: z-5500 hum hiss - updated :(

Fri Mar 05, 2010 2:55 pm

Just in case you haven't noticed, the OP now has a new problem and the unit is now actually nonfunctional.
There is a fixed amount of intelligence on the planet, and the population keeps growing :(
 
Jigar
Maximum Gerbil
Posts: 4887
Joined: Tue Mar 07, 2006 4:00 pm
Contact:

Re: z-5500 hum hiss - updated :(

Fri Mar 05, 2010 3:32 pm

morphine wrote:
Just in case you haven't noticed, the OP now has a new problem and the unit is now actually nonfunctional.


Missed that ... :oops:
Image
 
Digita1 Ecstasy
Gerbil In Training
Posts: 2
Joined: Mon Jun 07, 2010 3:27 pm

Re: z-5500 hum hiss - updated :(

Mon Jun 07, 2010 3:42 pm

Sorry to bring a dead thread back to life but, google searches are getting me nowhere.


I've had close to identical issues that OP had and have tried every possible solution brought up in the thread. I bought my z 5500's used, hooked up optically to my ps3, and coax to my pc. First time around there was very little humming, almost a whisper. If I used 6ch direct there was none. After moving the position of the sub further away from my tv, and to better the position of the surround sound the humming went from a whisper to having an unacceptably loud presence. It is unbearable to listen to these speakers at low volume now.


I tried unplugging and plugging everything back in. Logitech said florescent lightbulbs or dimmer switches in a room can cause interference (both of which my room has). Took them to another room, plugged directly into a wall. No gain. I eventually began to think it was the control pod to sub cable that was **** up. Wiggling it around, playing with the pin connector to the sub, or even fumbling the control pod upside down would decrease/increase the hum. Now doing any of that does nothing.


Also with my system hooked up properly, say when I am playing PS3 with optical input, the control pod will read that it detects nothing, only when live sound is present. (ie noise in a game, clicking around the XMB menu) During silence like load screens the hum will die, along with the audio signal and the control pod will go back to saying there's no input detected. These symptoms are identical when hooked up to my external sound card for my pc. Clues, anyone? Desperate here.

Edit: It's Firmware 2.0.4 - Control Pod PID is R608
Last edited by Digita1 Ecstasy on Mon Jun 07, 2010 3:58 pm, edited 1 time in total.
 
morphine
Gold subscriber
Gerbilus Supremus
Posts: 11398
Joined: Fri Dec 27, 2002 8:51 pm
Location: Portugal (that's next to Spain)

Re: z-5500 hum hiss - updated :(

Mon Jun 07, 2010 3:56 pm

Welcome to TR!

My apologies if I'm asking the obvious, but are those still in warranty? I'd simply take them back instead of wasting more time with them.
There is a fixed amount of intelligence on the planet, and the population keeps growing :(
 
cphite
Gerbil Elite
Posts: 883
Joined: Thu Apr 29, 2010 9:28 am

Re: z-5500 hum hiss - updated :(

Mon Jun 07, 2010 4:05 pm

I tried unplugging and plugging everything back in. Logitech said florescent lightbulbs or dimmer switches in a room can cause interference (both of which my room has). Took them to another room, plugged directly into a wall. No gain. I eventually began to think it was the control pod to sub cable that was **** up. Wiggling it around, playing with the pin connector to the sub, or even fumbling the control pod upside down would decrease/increase the hum. Now doing any of that does nothing.

Also with my system hooked up properly, say when I am playing PS3 with optical input, the control pod will read that it detects nothing, only when live sound is present. (ie noise in a game, clicking around the XMB menu) During silence like load screens the hum will die, along with the audio signal and the control pod will go back to saying there's no input detected. These symptoms are identical when hooked up to my external sound card for my pc. Clues, anyone? Desperate here.


My guess would be that a connection inside the unit is physically cracked at this point. The fact that you could change the hum by moving the unit around suggests that something was wiggling; and they fact that you can't do it anymore suggests that whatever that something was isn't wiggling anymore - it's either lodged or cracked in such a way that the wiggling no longer affects output.

Add to this the fact that it sees "no input" whenever there isn't actually sound playing at your source - and with different sources - suggests a bad connection within the unit itself.

You could try opening it up and looking for anything that looks loose or cracked. Before doing that, rule out bad cables etc.
 
Digita1 Ecstasy
Gerbil In Training
Posts: 2
Joined: Mon Jun 07, 2010 3:27 pm

Re: z-5500 hum hiss - updated :(

Tue Jun 08, 2010 1:32 pm

Thanks for a fast reply, and honestly. . . If I could return the speakers and get new ones I would. But I am a poor audiophile.


I'm pretty sure the problem lies within the control pod, or the VGA type connector to the sub. Maybe the cable too. How would I go about checking for a faulty cable? I opened up my control pod and took pictures. Everything seemed OK~ but I have an untrained eye. Everything seemed snug and in its place.


Image


Image
 
SergiuDan
Gerbil In Training
Posts: 1
Joined: Sat Nov 11, 2017 3:09 pm

Re: z-5500 hum hiss - updated :(

Sat Nov 11, 2017 3:12 pm

I am sending out this warning message to everyone owning a z5500 or z906 or any sound system from Logitech.
My system is about 5 years old, very good condition, bought second-hand two months ago. A couple days ago it started making an annoying hiss from the speakers. The humming sub was that way from the begging.
Anyway, I decided to open the sub and see what could be wrong. I was astonished when I saw that one of the wires, specifically the red one coming from the toroidal transformer, was missing from the bridge rectifier and was glued with silicone to the floor of the sub.There were just the other three wires connected to the bridge :two yellows and one black. So the system was working with a mono-phased bridge rectifier and the DC voltage it was providing to the main board was not as constant as with the full bridge working. You heard me right, the red wire had its connector GLUED with silicone to the base of the sub. The bridge rectifier is supposed to work using 4 diodes, but with the red wire disconnected, two of them were not used, for smoothing out the AC voltage. Now I am really mad at this company and specifically at the worker who could not get his **** together and connect all the wires properly,making such a big **** mistake. Anyone who is experiencing hissing in speakers and humming from the sub should CHECK THE BRIDGE RECTIFIER!!!
 
just brew it!
Gold subscriber
Administrator
Posts: 49429
Joined: Tue Aug 20, 2002 10:51 pm
Location: Somewhere, having a beer

Re: z-5500 hum hiss - updated :(

Sat Nov 11, 2017 4:09 pm

It was obviously working fine without the other phase until a couple of days ago. I think something else has failed.

Maybe post a pic?
Nostalgia isn't what it used to be.
 
Forge
Lord High Gerbil
Posts: 8220
Joined: Wed Dec 26, 2001 7:00 pm
Location: SouthEast PA

Re: z-5500 hum hiss - updated :(

Sat Nov 11, 2017 8:28 pm

Seven year necro? Is that a new record? My Z-680s have got to be 10+ years old now. The one rear sat has mouse holes chewed in the diaphragm and the backlight on the volume/controller pod is almost completely dead. Still sound pretty great though.
Behemoth - Plex server
Galactica - FreeNAS
Pegasus - R710 ESX host
fsociety - MBP 15
Rocinante - E5530 testing machine
Saratoga, Ticonderoga, BunkerHill - the Hydra desktop PC-thing.
 
HERETIC
Gerbil XP
Posts: 390
Joined: Sun Aug 24, 2014 4:10 am

Re: z-5500 hum hiss - updated :(

Sat Nov 11, 2017 10:32 pm

SergiuDan wrote:
I am sending out this warning message to everyone owning a z5500 or z906 or any sound system from Logitech.
My system is about 5 years old, very good condition, bought second-hand two months ago. A couple days ago it started making an annoying hiss from the speakers. The humming sub was that way from the begging.
Anyway, I decided to open the sub and see what could be wrong. I was astonished when I saw that one of the wires, specifically the red one coming from the toroidal transformer, was missing from the bridge rectifier and was glued with silicone to the floor of the sub.There were just the other three wires connected to the bridge :two yellows and one black. So the system was working with a mono-phased bridge rectifier and the DC voltage it was providing to the main board was not as constant as with the full bridge working. You heard me right, the red wire had its connector GLUED with silicone to the base of the sub. The bridge rectifier is supposed to work using 4 diodes, but with the red wire disconnected, two of them were not used, for smoothing out the AC voltage. Now I am really mad at this company and specifically at the worker who could not get his **** together and connect all the wires properly,making such a big **** mistake. Anyone who is experiencing hissing in speakers and humming from the sub should CHECK THE BRIDGE RECTIFIER!!!


The fact the wire was glued to the floor probably means it was designed like that.
If I remember correctly half wave gives 0.7 DC of AC voltage.
and full wave gives 1.4 X of AC voltage..............

Make sure all your connections are firm.
Check you'r not running any low-level audio cables parallel to power cables.
good luck.
 
ludi
Darth Gerbil
Posts: 7400
Joined: Fri Jun 21, 2002 10:47 pm
Location: Sunny Colorado front range

Re: z-5500 hum hiss - updated :(

Sun Nov 12, 2017 4:54 am

SergiuDan wrote:
I was astonished when I saw that one of the wires, specifically the red one coming from the toroidal transformer, was missing from the bridge rectifier and was glued with silicone to the floor of the sub.There were just the other three wires connected to the bridge :two yellows and one black. So the system was working with a mono-phased bridge rectifier and the DC voltage it was providing to the main board was not as constant as with the full bridge working.

Your astonishment may have diminished after studying the circuit more closely. This doesn't sound like a manufacturing botch-up, it sounds like a cheap-and-cheerful way of differentiating between 120 and 240V models without having to to modify any other components save the power cord. As long as the rectified DC is feeding into a switch mode power supply the extra ripple current doesn't matter much.
Abacus Model 2.5 | Quad-Row FX with 256 Cherry Red Slider Beads | Applewood Frame | Water Cooling by Brita Filtration
 
HERETIC
Gerbil XP
Posts: 390
Joined: Sun Aug 24, 2014 4:10 am

Re: z-5500 hum hiss - updated :(

Sun Nov 12, 2017 11:09 pm

ludi wrote:
Your astonishment may have diminished after studying the circuit more closely. This doesn't sound like a manufacturing botch-up, it sounds like a cheap-and-cheerful way of differentiating between 120 and 240V models without having to to modify any other components save the power cord. As long as the rectified DC is feeding into a switch mode power supply the extra ripple current doesn't matter much.


Your probably spot on there.
I might be a little out of date,but all that's required is a basic linear PSU-transformer-rectifier-smoothing capacitors.
with the size and quality of the capacitors the most important.
probably a chip amp that'll run on anything from 9 to 30 volts.
Most power amps run off a plus and minus supply-last I built for a 60 watt mosfet amp was 40-0-40....................

Who is online

Users browsing this forum: No registered users and 2 guests